In the face of the New Year, 2015, wire drawing machine wire drawing wheel what new operation requirements?
A, licensing requirements:
(1), the operator must hold a wire drawing machine operation certificate, it is strictly prohibited to unlicensed personnel computer operation.
[2], the operator must be conducted in the designated equipment production processing operation, it is forbidden to non-native personnel computer operation or string of bit operation.
(3), the operator must be familiar with the basic technical parameters and performance index of this device.
(4), the operator must be loyal to their duties, is responsible earnestly, familiar with the equipment operation, maintenance and maintenance.
5], summarize the operating personnel must constantly learning, its quality enhances unceasingly.
Second, the safe operation:
(1), the operator must wear gloves operation, in case of workpiece burn your fingers and affect the quality of the product.
2, should be check carefully before starting the equipment supply
(5 kg/cm2), whether the gas supply pipeline leak, drains water from the air filter.

(3), correct installation wiredrawing abrasive belt (wiredrawing abrasive belt inside the arrow direction with the direction arrow on wire drawing roller).Carefully check the upper and lower bearing seat and the lifting screw lubrication are in good condition, determine the material on the positive person to boot.
(4), the equipment after start-up should immediately check whether the abrasive belt swing is within the scope of the requirements, or other anomalies, otherwise should be dealt with immediately adjust or shutdown.
5], it is forbidden to wire drawing machine and dust collecting fan starts at the same time, the operation personnel leave work after it is strictly prohibited to boot.
[6], it is forbidden to artifacts need not directly on the conveyor belt, wire drawing, it is forbidden to leave work article no wood pallet block directly drawing, so as not to damage the conveyor belt and workpiece flew from cuts.
Once, when two people, in the rear of the equipment operation personnel shall not export of wire drawing machine, in order to avoid artifacts flying out of one thousand cuts.
Being, wire drawing machine pressure adjustment should be moderate, general pressure gauge instructions should be between 35 to 75, it is strictly prohibited to more than the red line, lest cause the equipment or personal accident.
'levies, equipment, it is forbidden to adjust the air pressure in the normal operation state, lest cause equipment, personal accident abrasive belt is out of control.
⑽, equipment in the process of running abnormal phenomenon, should immediately shutdown, power outages, so as to avoid failure.
⑾ should shut off the main power supply when maintenance, equipment, and brand operation is forbidden, lest cause an accident.
Long stay available, from work or equipment should be shut off the main power and compressed air, to ensure the safety of equipment.
Wire drawing machine wire drawing wheel operation requirements is such, hope I can help you.

The latest way of polishing wheel running out, together we look at the following content:
Polishing wheel can be divided into three ways:
1) the stitching the whole cloth wheel.Use soft cotton cloth is made, appropriate polishing complex shape workpiece, or for small workpiece fine polishing.
2) type of suture.Use cloth, non-woven fabrics and fine plain cloth, stitches can use concentric circles type spiral and straight form of radiation, appropriate polishing work of various kinds of coating and shape a simpler.
3) the wind cotton gauze round.USES 45 degrees of horn line cutting method, annular corrugated shaped, with a metal disk, middle has the characteristics of ventilation cooling, appropriate polishing large workpiece.
Polishing wheel used in various industries are very big, so here is a simple introduction.
Pay more attention to polishing wheel, please: xgdsq.cn

Jewels plane polishing wheel, it is a kind of pressure wheel, it consists of a number of polishing wheel piece of pressing, described each polishing the outer surface of the round pieces evenly coated with a layer of polishing oil reservoir.In polishing process does not need to be alone and go.It has simple structure, easy to use.The polishing effect is good.
The material of polishing wheel and polishing wheel is slightly different, it is made of elastic better all kinds of cotton cloth, fine felt, silk, made of deerskin, etc.In addition, in order to save and interlock fabric made of special paper cloth wheel has also been widely used.
Polishing wheel hardness with suture line distance to decide, the smaller the suture line distance, the higher the hardness of the polishing wheel.In order to make the softer in polishing wheel, polishing wheel production should pay attention to keep enough distance between stitches and wheel edges (also have no stitches).Polishing large workpiece, useful also have special air cooling device of the polishing wheel.
Polishing wheel can be divided into three ways:
1) the stitching the whole cloth wheel.Use soft cotton cloth is made, appropriate polishing complex shape workpiece, or for small workpiece fine polishing.
2) type of suture.Multi-purpose cloth, non-woven fabrics and fine plain cloth, stitches can adopt the concentric circles type spiral and direct radiation form, appropriate polishing all kinds of coating and shape a simpler job.
3) the wind cotton gauze round.USES 45 degrees of horn line cutting method, annular corrugated shaped, with a metal disk, middle has the characteristics of ventilation cooling, appropriate polishing large workpiece.

Nylon wheel is made of high qualified steel grit and glue them into a meticulously, nylon fiber, which can be widely used in the surface of the stainless steel, copper, iron and other metal products drawing, plastic, burr removing use, can also be used for grinding and polishing on the edge of the wood.Mainly used for the high requirements of the various metal lines processing, uniform sand grain straight, smooth finish.
Advantages:
The effect of cutting force, surface consistent.
Fiber flexibility, suitable for all kinds of the shape of the workpiece.
Self-sharpening sex is strong, not blocking slits, green nylon surface.
Durable, suitable for manual operation and automatic production.
No noise when grinding, less dust, accord with environmental protection requirement.

Huajie nylon wheel, you're worth it.Nylon wheel is made of high qualified steel grit and glue them into a meticulously, nylon fiber, which can be widely used in the surface of the stainless steel, copper, iron and other metal products drawing, plastic, burr removing use, can also be used for grinding and polishing on the edge of the wood.Mainly used for the high requirements of the various metal lines processing, uniform sand grain straight, smooth finish.
Advantages:
The effect of cutting force, surface consistent.
Fiber flexibility, suitable for all kinds of the shape of the workpiece.
Self-sharpening sex is strong, not blocking slits, green nylon surface.
Durable, suitable for manual operation and automatic production.
No noise when grinding, less dust, accord with environmental protection requirement.
Huajie nylon wheel, you're worth it.

Polishing wheel everyone not unfamiliar, but you know what it is to belong to industry?
Polishing wheel unit: composed of multi-layer combined material.
Polishing wheel: consists of a layer or multilayer polishing wheel unit, you can buy a finished product, combined together arbitrarily or it should be used for shaft.
Fran: is used to tighten metal polishing wheel.Pay per flange bite together so as to achieve the purpose of anti-skid.
Surface, side: be polishing wheel working surface.
The surface villi: a class of easy sticky polishing wax.
Polishing wax: it is a kind of applied to surface polishing wheel for grinding effect of the material, by abrasive, wax, grease, etc.Material from the coarse grinding of corundum powder to the best effect of gems have their own different USES.Abrasive polishing is cutting material, adhesive and wax, fat is the function of.
Level of cloth:
Normal, double agglutination and permeability
Outer diameter size, diameter of bore size
The number of slices, thickness
Standard stitch or a spiral suture
The introduction of polishing wheel is here now.